This Blog was posted for you By Your Electrician San Antonio – Good Electric
Repairing of Industrial Electronics & Automation Products
Our company provides Services for Repairing, Modification, and Automation for any Industrial Electronics & Automation Products. We are capable of handling any manufacturers like- Allen Bradley, ABB, AEG, Baumuller, Bosch, Control Techniques, Danfoss, Eurotherm, Fanuc, Fuji, General Electric, Hitachi, Honeywell, Indramat, Infranor, Landis, Lenze, Mitsubishi, Omron, Philips, Reliance, Sick, Siemens, Sprint, SSD, Telemecanique, Thorn, Schneider, Toshiba, Yaskawa, etc… We have substantial experience and repair facilities for equipment for all types of industry, specializing in the repair of AC Variable Frequency Drives (VFD), Power Supplies, Interface Boards, Controllers, Converters, Encoders, Input/output Cards, PLCs, HMI, Electronic Circuit Boards, etc.
We troubleshoot at a component level using industry-standard testing equipment. We use the test equipment to look for ‘electronic signatures’ from similar components to ascertain the component’s condition. If we suspect the component to be faulty, we replace it. We continue till all components have been tested on board. After replacing faulty components, we test and run the device through a series of power tests until we are satisfied with the device’s healthy working condition.
As per experience from many manufacturing industries, the breakdown of any machine is a direct loss of money every second. And it costs a huge amount. Therefore our repair cost is very nominal, and we provide faster electronics repair service to reduce your machine breakdown time and a diagnosis for the failure of your electronic instrument/device and guidance to avoid such failures in the future.
AC Drives/ VFD/ Inverter/ DC Drives/ Soft Starts/ Servo Drives/Servo Amplifiers.
We offer troubleshooting and repair of all types of AC drives/ DC drives and Soft-Starts from 1/8 to over 1000HP. About 70% of our work is in the AC drive area, as they are prevalent in any industrial process. Our technical staff will quickly find the reason for the fault or failure of your AC drive and advise you of your repair options.
PLC/PLC Cards (DI, DO, AI, AO & SMPS) Each PLC repair is disassembled and cleaned to remove contaminants.
Common failure rate components are replaced.
Unit is diagnosed, and failed components are replaced using OEM or better parts.
PLCs are tested utilizing OEM software, Our company’s own generated programs, and run tested in the OEMs PLC rack.
All jobs are static packed to protect the unit during shipment and storage.
Machine Tool/ CNCFor all Siemens and Fanuc Machine Tool Systems
We have the best equipment, best engineers, the best range of spare parts and the best test facilities. We are engaged in offering services for CNC Machine Control Cards Repairing, PC board repairing, industrial electronic and CNC board repair. The experts are instrumental in troubleshooting problems down to the chip level. We provide CNC Machine Control Card repairing services at a much lower cost than replacement parts.
Servo Motors
Carry out electrical checks and tests, resistance tests, insulation tests & inductance tests.
Check the condition of feedback devices.
If possible, run the motor & check against the specification.
The motor is dismantled.
Check bearing housings and shaft for concentricity.
Check mechanical tolerances.
Clean and degrease parts of the motor.
Remove and replace bearings and seals—reassembly of the motor.
Realign primary feedback device. Check and test any installed secondary feedback.
Complete test against OEM specification.
Test motor on OEM-specific AC Servo drive.
Spray finishes motor.
HMI/MMI/Industrial PC/Programmers/ Interface Boards
One of the most troublesome parts of any automation system is the display. Whether on a machine tool, part of a PLC system, or a custom-designed unit, our company can offer a comprehensive repair and refurbishment service.
All monitors and touch screens are disassembled and cleaned to remove contaminants.
Common failure rate components are replaced.
Unit is diagnosed and failed components are replaced using OEM or better parts.
Touch screens are tested using OEM software, PLC rack, or signal injection equipment.
All jobs are static packed to protect them during shipment and storage.
General Electronics/ Dedicated Controller/ OEMs Controller
Many of our customers want a comprehensive service to deal with their industrial electronic repair needs. This includes PSU, PCB, Process Control Instrumentation, and Test Instrumentation as well as General Electronics. Our company has risen to this challenge by diversifying into many other areas and gaining the necessary skills enabling us to offer this service with confidence.
Process Instrument (Flow Meters/ Pressure Regulators)
We offer troubleshooting and repair of all industrial flow meters/ Process instruments etc. Our technical staff will quickly find the reason for the fault or failure of the flow meter and advise you of your repair options. We repair all flow meters to the component level.
UPS Units & Power Supply Units/ Cards/ Chargers
All power supplies are disassembled and cleaned to remove contaminants.
Standard failure rate components are replaced.
Unit is diagnosed and failed components are replaced using OEM or better parts.
Each power supply repair is load-tested using variable resistive loads.
PS We might still do some of these repairs, call us to make sure.